Multi-band, dual independent receiver The IC-9100 covers 100W on HF, 50MHz and 144MHz, 75W on 430/440MHz bands and 10W on the 1200MHz band, for the 1200Mhz band the optional UX-9100 1200MHz band unit is required. The radio simultaneously receives two different bands (1. HF/50MHz + VHF/UHF, 2. VHF + UHF, 3. 430/440MHz + 1200MHz) and works as if there are two independent receivers in one radio. For example, you can arrange a 7MHz schedule QSO using a D-STAR repeater on VHF/UHF band, while watching 7MHz band activity using the simple band scope.
|
|
32-bit DSP & double conversion superheterodyne Much like the technology in Icom’s high-end HF radios, Icom has used a double conversion superheterodyne system and an image rejection mixer in the IC-9100’s HF to 430/440MHz bands. Each main and sub-receiver has a dedicated DSP unit providing fl exible digital IF fi lters, AGC time constant, twin PBT, manual and auto notch fi lter, noise reduction, noise blanker, etc. |
USB connector for PC control Modulator, received audio, RTTY demodulator, DV mode data can be transferred over the USB cable. By using appropriate 3rd party software, you can control as well as operate many of the digital modes via the single USB connection. Using the CI-V data format, the IC-9100 can be controlled by a PC through a USB or CT-17 level converter.
GPS position reporting functions The IC-9100 has a GPS button on the front panel. Your position data is shown on the display and can be sent to other stations in DV mode (Optional UT-121 D-STAR unit required. External GPS receiver can be connected via data 1 connector. Also, position data can be entered manually). When a calling station transmitting GPS data via DV mode is received, the IC-9100 displays the distance and direction to the station. GPS A mode is supported.
Satellite mode operation The satellite mode synchronizes the uplink (transmitting) and downlink (receiving) frequencies and shifts the frequencies in the same tuning step. 20 alphanumeric satellite memory channels store frequencies, operating mode and tone settings for quick setting.
Optional CS-9100 programming software When used with the optional CS-9100 programming software, alphanumeric memory channels, callsigns, filter widths and AGC settings can be easily made from a PC via USB cable connection. Share your memory channels info and radio settings.
RTTY demodulator and decoder The built-in RTTY demodulator and decoder allow you to read an RTTY message on the air instantly. No external units or PC required.
Optional 1200MHz band unit By installing the optional UX-9100 1200MHz band unit, the IC-9100 extends the coverage to the 1200MHz band. You can also enjoy L/V or L/U mode satellite operation.
And more....
- Built-in automatic antenna tuner for HF and 50MHz bands
- Band edge beep function
- Built-in voice synthesizer announces operating frequency, mode and S-meter level
- Electronic keyer jack on the front panel
- 4 channel CW mode memory keyer
- VSC (Voice Squelch Control) function
- Multi function meter shows signal strength, output power, SWR, ALC and compression level
- Main and sub-receiver external speaker connectors
GENERAL |
Frequency coverage: |
RX: |
0.030 ~ 60.000 MHz* 136.000 ~ 174.000 MHz* 420.000 ~ 480.000 MHz* 1240.000 ~ 1320.000 MHz** |
TX: |
1.810 ~ 1.999 MHz 3.500 ~ 3.800 MHz 7.000 ~ 7.200 MHz 10.100 ~ 10.150 MHz 14.000 ~ 14.350 MHz 18.068 ~ 18.168 MHz 21.000 ~ 21.450 MHz 24.890 ~ 24.990 MHz 28.000 ~ 29.700 MHz 50.000 ~ 52.000 MHz 144.000 ~ 146.000 MHz 430.000 ~ 440.000 MHz 1240.000 ~ 1300.000 MHz** |
*Some frequency bands are not guaranteed **With UX-9100 optional unit |
|
Mode: |
USB, LSB, CW, RTTY, FM, AM (Transmit: HF/50MHz only, Cannot receive on 1200MHz band), DV (with UT-121 optional) |
No. of memory Ch: |
297 Ch (99 Ch for each band) 3 call Ch (1 Ch for each band) 18 scan edges (6 Ch for each band) 20 satellite memories 26 GPS memories |
Antenna impedance: |
50 ohm |
Antenna connector: |
HF/50MHz |
SO-239 |
144MHz |
SO-239 |
430/440MHz |
Type-N |
Temperature range: |
0°C to +50°C |
Frequency stability: |
Less than ±0.5ppm (0°C to +50°C ) |
Power supply: |
13.8V cc ±15% |
Current drain: |
Tx Max power: |
24A |
Rx Max. audio: |
5.5A |
Dimensions: |
315 (W) x 116 (H) x 343 (D) mm |
Weight: |
11 kg. |
|
TRANSMITTER |
Output power: |
Band/Mode |
SSB, CW, RTTY, FM, DV |
AM |
HF/50MHz: |
2 ~ 100W |
2 ~ 25W |
144MHz: |
2 ~ 100W |
- |
430/440MHz: |
2 ~ 75W |
- |
Spurious emission: |
< -50dB (1.8 ~ 29.995MHz) < -63dB (50MHz/144MHz) < -61dB (430/440MHz) |
Carrier suppression: |
> 40dB |
Unwanted sideband suppression: |
> 55dB |
|
RECEIVER |
Intermediate frequencies: |
HF/50MHz |
64.455 MHz, 36 kHz |
144MHz |
10.850 MHz, 36 kHz |
430/440MHz |
71.250 MHz, 36 kHz |
Sensitivity: |
Band/MHz |
0.5-1.8 |
1.8-29.9 |
50-54 |
144/440 |
SSB-CW |
- |
0.20µV |
0.16µV |
0.11µV |
AM |
15.8µV |
2.5µV |
2.0µV |
1.4µV |
FM |
- |
0.63µV (28-29.7) |
0.40µV |
0.18µV |
DV |
- |
1.26µV (28-29.7) |
0.79µV |
0.35µV |
SSB/CW,AM: 10dB S/N FM: 12dB SINAD DV: 1% BER Preamp1 ON: 0.5-1.8/1.8-29.9MHz Preamp2 ON: 50-54MHz |
|
Selectivity: |
SSB (BW=2.4kHz) |
2.4kHz/-6dB; 3.8kHz/-60dB |
CW: (BW=500Hz) |
500Hz/-6dB; 900Hz/-60dB |
RTTY: (BW=350Hz) |
350Hz/-6dB; 650Hz/-60dB |
AM: (BW=6kHz) |
6.0kHz/-6dB; 15kHz/-60dB |
FM: (BW=15kHz) |
12.0kHz/-6dB; 20kHz/-60dB |
DV: (12.5kHz spacing) |
>-50dB |
|
Spurious and image rejection ratio: |
HF/50MHz |
>70dB |
144/440MHz |
>60dB |
Audio output: |
> 2.0W (8 Ohm load, 10% dist.) |
| |